Applications of numerical optimization techniques to design of axial compressor blades

This paper describes the shape optimization of NASA rotor 37 and rotor and stator blades in a single-stage transonic axial compressor.Shape optimization of the blades operating at the design flow condition has been performed using the response surface method and three-dimensional Navier-Stokes analysis.Thin-layer approximation is introduced to the Navier-Stokes equations,and an explicit Runge-Kutta scheme is used to solve the governing equations.The three design variables,blade sweep,lean and skew,are introduced to optimize the three-dimensional stacking line of the blades.The objective function of the shape optimization is an adiabatic efficiency.Throughout the optimization of rotor and stator blades, optimal blade shape can be obtained.It is noted the increase of adiabatic efficiency by optimization of the blade shape with the stacking line in the single-stage transonic axial compressor is more effective in a rotor blade rather than a stator blade because of the large deformation of blade shape in the stator blade.      

An annual variation analysis of the ionospheric spatial gradient over a regional area for GNSS applications

An ionospheric spatial gradient represents the ionosphere delay difference between different locations, and its variation over a specific area is important for implementing differential GNSS systems. An estimation method for the ionospheric spatial gradient over a small regional area is proposed. A plate map model is implemented for the direct estimation of the gradients. Nine years of GPS data were processed to figure out the annual variation of the mean gradient at the mid-geomagnetic latitude of 30° N. Gradients along the north–south direction have a mean of 0.65 mm/km and follow solar-cycle variations.     

Statistical analysis of geomagnetic field variations during solar eclipses

We investigate the geomagnetic field variations recorded by INTERMAGNET geomagnetic observatories, which are observed while the Moon’s umbra or penumbra passed over them during a solar eclipse event. Though it is generally considered that the geomagnetic field can be modulated during solar eclipses, the effect of the solar eclipse on the observed geomagnetic field has proved subtle to be detected. Instead of exploring the geomagnetic field as a case study, we analyze 207 geomagnetic manifestations acquired by 100 geomagnetic observatories during 39 solar eclipses occurring from 1991 to 2016. As a result of examining a pattern of the geomagnetic field variation on average, we confirm that the effect can be seen over an interval of 180?min centered at the time of maximum eclipse on a site of a geomagnetic observatory. That is, demonstrate an increase in the Y component of the geomagnetic field and decreases in the X component and the total strength of the geomagnetic field. We also find that the effect can be overwhelmed, depending more sensitively on the level of daily geomagnetic events than on the level of solar activity and/or the phase of solar cycle. We have demonstrated it by dividing the whole data set into subsets based on parameters of the geomagnetic field, solar activity, and solar eclipses. It is suggested, therefore, that an evidence of the solar eclipse effect can be revealed even at the solar maximum, as long as the day of the solar eclipse is magnetically quiet.     

Orbit determination performances using single- and double-differenced methods: SAC-C and KOMPSAT-2

In this paper, Global Positioning System-based (GPS) Orbit Determination (OD) for the KOrea-Multi-Purpose-SATellite (KOMPSAT)-2 using single- and double-differenced methods is studied. The requirement of KOMPSAT-2 orbit accuracy is to allow 1 m positioning error to generate 1-m panchromatic images. KOMPSAT-2 OD is computed using real on-board GPS data. However, the local time of the KOMPSAT-2 GPS receiver is not synchronized with the zero fractional seconds of the GPS time internally, and it continuously drifts according to the pseudorange epochs. In order to resolve this problem, an OD based on single-differenced GPS data from the KOMPSAT-2 uses the tagged time of the GPS receiver, and the accuracy of the OD result is assessed using the overlapping orbit solution between two adjacent days. The clock error of the GPS satellites in the KOMPSAT-2 single-differenced method is corrected using International GNSS Service (IGS) clock information at 5-min intervals. KOMPSAT-2 OD using both double- and single-differenced methods satisfies the requirement of 1-m accuracy in overlapping three dimensional orbit solutions. The results of the SAC-C OD compared with JPL’s POE (Precise Orbit Ephemeris) are also illustrated to demonstrate the implementation of the single- and double-differenced methods using a satellite that has independent orbit information available for validation.     

Sensitivity analyses of satellite propulsion components with their thermal modelling

Performing the sensitivity analyses of the contact conduction and the position of thermostat on the basis of the thermal model established, the study of thermal design is accomplished for the preparation of possible mechanical interface change of the satellite propulsion system depending on the satellite system design. A relatively simple thermal model is taken into consideration for the convenience of the analysis. A variety of the spacecraft bus voltages and the contact resistances are examined as well as the position of thermostat on propulsion components. As a consequence, even though the mechanical interface condition is changed on the same module, the successful thermal design could be achieved if we design the heater to have sufficiently large power with reference to the heritage value of contact resistance. Besides the reasonable performance on the thermal control is assured with the thermostat location errors, if the uncertainty in the position of thermostat is not quite large when assembling tank module.     

Monitoring atomic clocks on board GNSS satellites

A method for monitoring atomic clocks on board Global Navigation Satellites System (GNSS) satellites is described to address the issue of clock related signal integrity in safety–critical applications of GNSS. The carrier-phase time transfer is employed in the clock monitoring method which enables tight tracking of the satellite onboard clocks and thus improves detectability of clock anomalies. Detecting onboard clock anomalies requires the ability to monitor clocks in real time, and a Kalman filter can then be utilized to estimate the phase offsets between the satellite clocks and ground clocks. This study, using the difference between the measured and predicted phase offset as a test statistic, sets a threshold for clock anomalies based on the prediction interval approach. Finally the validity of the monitoring method is examined by processing a set of real GNSS data that includes two recent incidents of clock anomalies in GNSS satellites.     

Development of multi-functional composite structures with embedded electronics for space application

Conventional spacecraft structural function has been limited to supporting loads and mounting avionics only. In contrast, the technology of ‘multi-functional structures’ can integrate thermal and electronic functions into the spacecraft’s inherent load-bearing capability. In addition, sufficient radiation shielding effectiveness can be provided for the anticipated mission environment. Utilizing this concept, the ratio of electrical functionality to spacecraft volume can be dramatically increased and significant mass savings can be obtained. In this paper, spacecraft electronics are miniaturized using advanced IT applications such as flexible circuitry, miniaturized components, featherweight connectors, and so on, that they can be easily embedded within a structural panel. A sandwich structural panel consists of an aluminum honeycomb core and lightweight CFRP facesheets. Integration of electronics is implemented within the panel by mounting electronics on a multi-layered composite enclosure with multi-materials. This composite enclosure provides a load-bearing, effective thermal conduction, radiation shielding capabilities and an available space for embedding electronics. A series of environmental tests and analyses is carried out to demonstrate that the flight hardware is qualified for the expected mission environments. This approach will be utilized for the advanced small satellite ‘STSAT-3’ to validate the multi-functional structures concept.     

Design and implementation of the flight dynamics system for COMS satellite mission operations

The first Korean multi-mission geostationary Earth orbit satellite, Communications, Ocean, and Meteorological Satellite (COMS) was launched by an Ariane 5 launch vehicle in June 26, 2010. The COMS satellite has three payloads including Ka-band communications, Geostationary Ocean Color Imager, and Meteorological Imager. Although the COMS spacecraft bus is based on the Astrium Eurostar 3000 series, it has only one solar array to the south panel because all of the imaging sensors are located on the north panel. In order to maintain the spacecraft attitude with 5 wheels and 7 thrusters, COMS should perform twice a day wheel off-loading thruster firing operations, which affect on the satellite orbit. COMS flight dynamics system provides the general on-station functions such as orbit determination, orbit prediction, event prediction, station-keeping maneuver planning, station-relocation maneuver planning, and fuel accounting. All orbit related functions in flight dynamics system consider the orbital perturbations due to wheel off-loading operations. There are some specific flight dynamics functions to operate the spacecraft bus such as wheel off-loading management, oscillator updating management, and on-station attitude reacquisition management. In this paper, the design and implementation of the COMS flight dynamics system is presented. An object oriented analysis and design methodology is applied to the flight dynamics system design. Programming language C# within Microsoft .NET framework is used for the implementation of COMS flight dynamics system on Windows based personal computer.     

Searching for biosignatures using electron paramagnetic resonance (EPR) analysis of manganese oxides

Manganese oxide (Mn oxide) minerals from bacterial sources produce electron paramagnetic resonance (EPR) spectral signatures that are mostly distinct from those of synthetic simulants and abiogenic mineral Mn oxides. Biogenic Mn oxides exhibit only narrow EPR spectral linewidths (～500 G), whereas abiogenic Mn oxides produce spectral linewidths that are 2-6 times broader and range from 1200 to 3000 G. This distinction is consistent with X-ray structural observations that biogenic Mn oxides have abundant layer site vacancies and edge terminations and are mostly of single ionic species [i.e., Mn(IV)], all of which favor narrow EPR linewidths. In contrast, abiogenic Mn oxides have fewer lattice vacancies, larger particle sizes, and mixed ionic species [Mn(III) and Mn(IV)], which lead to the broader linewidths. These properties could be utilized in the search for extraterrestrial physicochemical biosignatures, for example, on Mars missions that include a miniature version of an EPR spectrometer.